How to Install L Track Anchor Tie Down Points on your Truck or Trailer

Learn how to install 2″ L Track round anchor tie-down points. This installation job is pretty straightforward and shouldn’t take more than an hour or two when you have the right tools and proper instructions.

DIY Installation Video Below

Installing L-Track, or logistic track, on your truck or trailer gives you secure tie down points right where you need them. There are many other benefits to installing L track as a tie-down system, and there are also some key differences between L track and E track.

In the video below, we show you how to install 2″ L Track round anchor tie-down points. This installation job is pretty straightforward and shouldn’t take more than an hour or two when you have the right tools and proper instructions.

Tools Needed:

  • Cordless Drill with 1/4″ Drill Bit
  • Philips Screwdriver
  • 7/16 Wrench
  • Tape Measure
  • Sharpie Marker

https://www.youtube.com/watch?v=ICZ3mWkz7wM?rel=0

The 2″ Round Anchor Point Tie Down Kit comes with four sets of anchors, bolt plates, rings, and fasteners. In this video, we install two L track anchor points on a truck bed floor and two on the front wall. To install L track tie downs on a trailer, the required steps are essentially the same.

L Track Anchor Point Installation Steps:

  1. Use a tape measure to determine your install point. Place the anchor in the intended spot and mark both holes using the sharpie.
  2. Using a cordless drill with 1/4″ bit, drill through the truck bed to create the two installation holes.
  3. Place an anchor over the holes and insert two screws.
  4. From the underside of the truck, install a bolt plate through the two fasteners then add nuts and tighten with a wrench.
  5. Once your anchors are tightly secured, you can install the removable tie down ring. Grasp the base of the ring while pushing the center down with your thumb. Slide it into place over the anchor and release to lock it into place.

Tip: To install these L track anchor points in tight spots, like the front wall of a truck bed, it’s helpful to hold your wrench on the nuts while you tighten the screws from the other side with a screwdriver.

installing l track tie downs

More L Track Tips

Remember to release and remove your tie down rings if your hauling cargo that doesn’t require using your new tie down points. It doesn’t take long to remove and replace them, and it will help prevent unwanted damage.

If you’d rather have compact strips of aluminum L-track serve as the anchor for your removable tie-down rings, see our 6-piece 4-inch L Track Tie Down System that works great on enclosed trailer walls as well as truck bed floors and rails. The benefit of this system is that you can quickly and easily adjust where your anchor points sit along the 4-foot rails.

If you’re hauling motorcycles and want the ultimate hold on your bike with the versatility of L-track, check out the TrackStar L-track Motorcycle Chock that’s light and easy to handle but durable and reinforced with powder-coated tubular steel construction.

For all tie down rail options, see our Airline Track & L-Track Tie Down Rails page.

How to Install L-Track Singles

23573-anchor-point-tie-down-kit-w-round-base_1_375
2″ Round Anchor Point Tie Down Kit (#APK2RBL)

l-track singles from US Cargo ControlLike L-track rails, L-track singles are incredibly versatile. They’re great for adding a tie down point just where you need it, but the small size offers up even more options than a full length track.

In this video, we installed our 2″ Track Anchor Point Tie Down System, which includes 4 sets of a round anchor, bolt plate, ring, and fasteners. This kit is also available with rectangular anchor points here: 2″ Track Anchor Point Tie Down System-Rectangular.

We set up this system with two points secured to the floor and two on the front wall of the truck bed.

Products used:

Tools required:

  • Cordless drill with 1/4 inch drill bit
  • Philips screwdriver
  • 7/16 wrench
  • Tape measure and Sharpie marker

To shop our entire line of motorcycle tie downs, click:

L-Track Fittings and Installation

While E track tie downs have been the traditional favorite for flat trailers and enclosed trailer tie downs, L track tie down systems (also called logistic track or airline track) is gaining in popularity. Because of its lower profile, airline track tie down rail and fittings are ideal for smaller spaces like truck beds. In addition to lengths of logistic track tie down rail, single track pieces are also available in a 2′ round or 2″ rectangular style so you can create single anchor points wherever you need them. And with range of l track fittings, and even ratchet straps outfitted with both e-track and l-track fittings, becoming more widely available, these slim, sleek cargo tie downs can be used to easily and quickly secure just about anything.

See our entire selection of L track tie down systems, and check out these videos for tips on installing l-track and choosing the right fittings for your tie downs:

How to install L-track:

L-track fittings:

 

L-track fittings featured in these videos:

How to Create Tie Down Points Using L Track Single Receivers

This video explains the uses for our airline track single receivers and single stud fittings with o-rings. This item features a 2″ round base with two holes for mounting on pickup beds, RV’s, trailers, etc. The spring-loaded plunger squeezes easily to slide into the base and snap in place. It can be used to tie down motorcycles, ATV’s, lawn mowers, snowmobiles and any other cargo you need to secure.

The logistic track single receivers can be mounted virtually anywhere you need an anchor point for a tie down. The 2″ base is as strong as the fitting itself, and depends on strong fasteners to hold it down. You want to use solid fasteners, preferably a bolt or machine screw, that’s going to go all the way through what your mounting to. Don’t forget a nut and washer on the back side.

Once your receivers are fastened, your items can be strapped down using a ratchet strap with an s-hook, bungee cords, rope or anything else that is suitable. Check out our motorcycle combo strap kit that includes tie down straps with s-hooks for use in your assembly.

For more information or to purchase the items in this video, click on the links below:

View our Anchor Point Tie Down Kit below:

How To Create a Motorcycle Tie Down System in a Pickup Truck Using LTrack

This video shows how L-track (also known as L track, airline track or logistic track) is used to create a motorcycle tie down system in a pickup truck. L-track installed on a the bed rails of a truck provides a wide variety of anchor points to tie down motorcycles, ATVs or other cargo you want to haul.

For more information or to purchase the items in this video, click on the links below:

View all motorcycle tie down system kits.