A Complete Guide to Flatbed Trailer Tarps

Flatbed trailer tarps protect cargo from weather damage and general wear-and-tear that highway travel can cause. Tarps are waterproof and often made of vinyl, kevlar, or canvas with a polyethylene coating for added protection. Read on to understand the differences among types of flatbed trailer tarps, how to properly tarp a flatbed trailer, and how to repair a torn tarp.

 

Types of Flatbed Tarps

The type of tarp you should use depends on what you are hauling and how big it is. Not all tarps are created equal.

 

Lumber Tarps

how to use a lumber tarp

 

 

 

 

 

Lumber tarps are used on loads that are tall and box-shaped. They have flaps at each end to cover the ends of lumber. Both the sides and tail flap of a lumber tarp are usually fitted with grommets and multiple rows of D-rings for a variety of tie-down points. Usually, two lumber tarps are used to cover a flatbed load.

 

Steel Tarps

how to use steel tarps

 

 

 

 

 

Steel tarps on the most commonly used flatbed trailer tarp. They will also typically have grommets and D-rings built-in, however no flaps. They are used to protect shorter and lower-profile loads, and also used in combination with lumber tarps.

 

Smoke Tarps

how to use a smoke tarp

 

 

 

 

 

Smoke tarps only cover the upper front portion of a flatbed load. This protects loads from getting covered in exhaust fumes and dirt. They can also be used in combination with steel and lumber tarps when additional coverage is needed.

 

Machinery Tarps

how to use a machine tarp

 

 

 

 

 

 

Machinery tarps are designed to protect manufacturing or machine equipment from weather and road vibration. These heavy-duty tarps have grommets around the hems and multiple rows of D-rings on each side.

 

Coil Tarps

how to use coil tarps

 

 

 

 

 

 

Coil tarps are commonly used to protect steel or aluminum coils and cable spools during transport. Their rounded top-half allows for a fitted cover over cylinder-shaped loads. The side flaps are more rectangular shaped and split in each corner to allow transport chain to pass through.

 

How to Tarp a Flatbed Trailer Load

A tarp is only effective if it’s applied correctly and secured tightly. Follow these step for tarping a load on a flatbed trailer.

 

flatbed tarping

1. Lift your rolled-up tarp on top of the load and center it as best as you can.

2. You should always start from the back of your load. Start unrolling the tarp towards the back while keeping the centerfold of the tarp in the center of the load.

3. Once the tarp is unrolled, pull the bottom of the tarp so that it is covering the entire back of the load and touching the flatbed trailer.

4. Next, start unfolding the tarp once on each side, making sure it stays center.

5. If you are using multiple tarps repeat the steps above to cover any exposed cargo.

6. Once your tarps have been completely unrolled and your load is covered, roll up or fold in any excess tarp and secure the D-rings with bungee cords.

7. If your load is tall or oddly shaped, throw an extra tie-down strap over the tarp to prevent it from billowing.

 

How to Repair Tarps

Eventually, weather and prolonged use wear down tarps to the point that they must to be repaired to remain effective.

how to repair a tarp

  1.  Buy a flatbed tarp repair kit.
  2. Place the tarp on a flat surface with the underside facing up. Smooth out any wrinkled areas.
  3.  Cut a patch slightly larger than the tear.
  4.  Apply a heavy layer of tarp repair adhesive to one side of the patch and place over the tear.
  5.  Use a roller to smooth out and remove any air bubbles. Let dry for at least three hours.

 

Custom Tarps and Other Flatbed Equipment

Shop US Cargo Control for all your flatbed trailer equipment needs, including winch straps, winch bars, and custom tarps.

 

,



Subscribe To Messages From US Cargo Control

Please enter your email address
 to subscribe to new articles from this blog. Select if you would also like to receive exclusive discounts, sales and promotional messages. When you are done press Subscribe.
 
 

2 Responses to A Complete Guide to Flatbed Trailer Tarps

  1. Ron Anderson July 30, 2018 at 6:24 PM #

    How many different weights of tarp are there? How are they rated?

    • Colton Radford July 31, 2018 at 11:15 AM #

      Ron – tarp weights are determined by the weight of a square yard (3’x3′) of material. Depending on the tarp material, tarps can weigh anywhere from 2oz up to 40oz plus. However, when it comes to the trucking industry, the most common tarp weights are 14oz and 18oz. US Cargo Control offers tarps in both these weights, and in some cases, we make trucking tarps with 18oz weight on the top and 14oz weight on the side flaps. 18oz is considered heavy duty, but 14oz will obviously be slightly lighter and easier to manage on a daily basis.

%d bloggers like this: